플라스틱 펠릿용 진동 스크린: 미분 제거 및 과립 분급

A vibrating screen for plastic pellets helps remove fines and broken particles while separating granules by size. In a linear vibrating screen, material moves across the screen surface: particles smaller than the openings pass through, while larger pellets continue to the discharge outlet. If the line also needs to reject oversized pellets, additional screening cuts can produce separate fines, acceptable pellet, and oversize streams. The right screen openings, number of decks, and feed rate depend on your pellet size range and required capacity.

플라스틱 펠릿용 진동 스크린

Why Screen Plastic Pellets?

A vibrating screen for plastic pellets helps keep undersized fragments and oversized granules out of the acceptable product stream. For PE, PP, or recycled pellets, the screening goal depends on the size range the next process or customer requires. A vibrating screen separates material according to whether particles can pass through its openings; it does not identify a particle’s material or remove every contaminant.

Remove Fines and Broken Pellets

Pellet handling can generate small fragments and loose fines. With an appropriately sized screen, these smaller particles pass through while acceptable pellets travel toward the discharge outlet. This is useful before packaging or feeding pellets into the next process. Very fine dust that clings to pellets because of static electricity may also require dust extraction or another cleaning step.

Separate Acceptable Pellets from Oversized Granules

If the feed contains both undersized and oversized pieces, two screening cuts can divide it into three streams. For example, suppose the specified pellet size range is 2–4mm:

Material sizeScreening goal배출
Below the lower cut pointRemove fines and undersized fragmentsUndersize outlet
Within the specified rangeKeep acceptable pellets제품 배출구
Above the upper cut pointReject oversized or joined pellets과대 배출구

This is an illustrative layout, not a universal recommendation for 2 mm and 4 mm screen openings. Elongated pellets and particles close to an opening may behave differently from their nominal size.

Where Screening Fits in a Pellet Handling Line

A plastic pellet screen can be placed after pelletizing and cooling, or before storage, conveying, or packaging, depending on where fines and oversize are generated. Screening close to the final product transfer point helps control the size of pellets entering the next stage. The location should allow steady feeding and separate collection of each discharge stream.

Linear Vibrating Machine
선형 운동 진동 스크린은

How Does a Vibrating Screen for Plastic Pellets Separate Fines?

A 선형 진동 스크린 moves plastic pellets across one or more screen decks. Each deck creates a size cut: particles small enough to pass through its openings move to the outlet below, while larger particles continue across the deck. The number of cuts depends on whether the line needs only fines removal or separate fines, acceptable pellets, and oversize.

How Pellets Move Across the Screen

Two counter-rotating vibration motors produce a forward, bouncing motion. As pellets travel across the screen, smaller particles have opportunities to pass through the openings. A steady feed helps spread material across the available screen area; where needed, a feed distributor can reduce concentrated impact at the inlet. Feed rate and vibration settings should suit the pellets so material moves forward without passing over the screen too quickly.

One Screen for Fines Removal

When the only goal is to remove undersized fragments, one screening cut may be enough. Fines pass through the screen, while pellets too large to pass continue to the product outlet. This setup does not separately reject oversized pellets: they remain with the retained product unless another screening cut is added.

Two Screening Cuts for Three Output Streams

To remove both oversize and fines, an upper deck first retains oversized pieces. Material passing through it reaches a lower deck, where acceptable pellets remain on the screen and fines pass through.

Screening stageMaterial separated배출구
Upper deck, retainedOversized pellets or joined pieces기준 초과물
Lower deck, retained적합한 펠릿제품
Lower deck, passed through미분과 기준 미달 조각Undersize

Each outlet should be kept separate. An enclosed cover can also be specified with a connection to the plant’s dust extraction system when loose fines create dust during feeding and discharge.

What Affects Screening Capacity and Separation Quality?

The performance of a vibrating screen for plastic pellets depends on more than motor power. Feed rate, pellet size and shape, open screen area, and the way material moves across the deck all affect how many fines reach the openings before discharge. Settings that work for coarse PP pellets may not work for a feed containing much finer PC particles. When capacity falls or fines remain in the product, identify the cause before increasing vibration.

Feed Rate and Pellet Bed Depth

A heavy or uneven feed forms a deep layer of pellets. Fines trapped within that layer have fewer opportunities to reach the screen, so they may leave through the product outlet. Check whether material is spread across the full screen width. A feed distributor and a steadier feed rate can improve screen use without changing the motor settings.

Pellet Shape, Moisture, and Static Buildup

Round pellets, irregular recycled granules, and flat or elongated pieces do not pass through the same opening in exactly the same way. Damp or static-charged fines may cling to pellets or the screen rather than separate cleanly. Check the feed condition, control moisture where appropriate, and assess static control as part of the conveying and dust-handling system. A nominal pellet diameter alone does not determine the correct screen opening.

Near-Size Particles and Screen Blockage

Particles close to the opening size can lodge in the apertures. A compatible bouncing-ball cleaning system may help dislodge physically trapped particles. If fines mainly adhere because of static, mechanical cleaning alone may have limited effect; check equipment grounding and material-handling conditions. Our guide to industrial screen clogging explains other causes and cleaning options.

Screen Area, Vibration Settings, and Discharge Layout

Increasing vibration is not always the answer. If pellets move off the deck too quickly, fines have less time to pass through; if movement is too slow, material can build up and restrict capacity. Review screen area, feed distribution, material travel, and separation at each outlet together. Settings should suit the polymer, pellet size, and target throughput rather than follow one fixed configuration.

Observed problemCheck firstPossible adjustment
Fines remain in the productFeed depth and travel timeSpread or reduce the feed; review vibration settings
Good pellets enter the undersize outletScreen opening and pellet shapeRecheck the required size cut
Openings repeatedly blockNear-size particles, moisture, or staticMatch the cleaning method to the cause
Capacity falls during operationBlocked screen area or uneven feedingClear the blockage and stabilize the feed

How to Specify a Plastic Pellet Vibrating Screen for Your Line

To specify a vibrating screen for plastic pellets, define three requirements first: the material being screened, the acceptable pellet size range, and the required hourly capacity. These determine the screen openings, number of decks, screen area, and discharge layout.

제공할 정보

Specify the polymer type, such as PE, PP, or ABS; whether the pellets are virgin or recycled; their size and shape; and any moisture or static problems. Include the proportion of fines and oversize, required capacity in kg/h or t/h, available installation space, and whether the screen must connect to a dust extraction system.

For example, a recycled-plastic line may need to reject pieces over 5 mm, collect 1–5 mm pellets as product, and discharge material below 1 mm as undersize. This is a separate example from the 2–4 mm specification above. If material below 0.5 mm must be recovered separately from the remaining undersize, it needs an additional size cut and outlet.

Configuration Points to Confirm

Choose screen openings according to the required cut points in millimeters, and match the number of decks to the number of output fractions. Confirm that each outlet can connect to the intended collection or conveying system. Also check contact materials, access for screen cleaning, and the dust connection.

Yuanjing의 linear vibrating screen for plastic granules supports different screen configurations for grading. The final arrangement should match the stated size range, capacity, and production-line layout.

자주 묻는 질문

가장 작은 허용 가능한 펠릿 크기에 따라 개구부를 선택하고, 폴리머 이름만으로 결정하지 마십시오. 통과하는 입자는 미립자 스트림이 되고, 잔류하는 펠릿은 제품 출구로 계속 이동합니다. 절단점을 밀리미터 단위로 지정하고 불규칙하거나 길쭉한 펠릿을 고려하십시오.

예. 두 개의 스크리닝 컷을 갖춘 선형 진동 스크린은 과대 조각, 허용 가능한 펠릿, 미분을 세 개의 배출구로 분리할 수 있습니다. 하나의 컷만으로는 미달 크기를 제거하지만 과대 조각은 잔류 펠릿과 함께 남습니다.

네, 재생 PE, PP, ABS 및 기타 플라스틱 과립을 크기별로 분급할 수 있습니다. 재생 원료에는 불규칙한 조각, 서로 붙은 펠릿 또는 미분이 더 많이 포함될 수 있으므로, 투입 원료와 필요한 제품 입도 범위에 맞게 체 구멍과 배출구 배치를 정해야 합니다.

처리 용량은 펠릿의 크기와 모양, 미분량, 스크린 구멍 크기, 유효 스크린 면적 및 공급 속도에 따라 달라집니다. 제시된 기계 처리 용량이 모든 재료에 대해 동일한 처리량을 보장하는 것은 아닙니다. 필요한 처리량을 kg/h 또는 t/h 단위로 펠릿 크기 범위와 함께 제시하십시오.

먼저 입자가 개구부에 물리적으로 끼어 있는지, 아니면 대전된 미분이 스크린에 달라붙어 있는지 확인하십시오. 적절한 망 세척 시스템은 끼어 있는 입자를 제거하는 데 도움이 될 수 있습니다. 정전기로 인한 부착은 접지, 원료 취급 및 분진 관리에 주의를 기울여야 합니다. 진동을 단순히 증가시키는 것만으로는 어느 쪽 원인도 해결되지 않을 수 있습니다.

일반적인 설치 위치는 펠릿화 및 냉각 후 또는 보관 및 포장 전입니다. 다음 단계 전에 미분이나 규격 초과 조각을 제거해야 하며, 별도의 배출구, 유지보수 접근 및 집진 설비 연결을 위한 공간이 있는 위치를 선택하십시오.

Related application: Feed pellet screening before bagging — screen selection, fines removal, and handling considerations for fragile feed pellets.

관련 기사